To clean a shower head (plus why you need) (2024)

If your shower only supplies a trick of water, you may need to clean the shower head.Water, even from a municipal system, contains minerals that build up and block the openings in the shower head.And if you live in an area of hard water or use good water, the problem can be even worse.

Installation of oneGood shower filterCan help reduce mineral deposits and contaminants.But when the openings or nozzles are blocked, the shower head is a dark, moist, warm place for bacteria and fungus to grow.Gross!It is time to learn how to clean your shower head as effectively as possible.Follow the steps below - and you can be tempted to act with yourRelaxing bathFor aRelaxing shower.

How often to clean a shower head

If you have never cleaned the shower head or there is a reduced water flow, it must be cleaned immediately.Put a regular memory on your phone to thoroughly thoroughly clean the shower head every two months or more often if you live in an area of hard water.Control cleaning will also help to limit the fungus and bacterial growth in the shower head.

What you need:

To clean with vinegar

• Distilled white vinegar orCleaning of vinegar
  
• Powerful storage bag with plastic food
• Rubber band or twist -tape
• What
• Toothpicks
• Sodium carbonate

To clean with lemon juice

• Old toothbrush
• Sodium carbonate
• Salty
• Lemon juice

To clean the filter screen

• Wrench or lockable tongs
• Needle -nosy seaweed
• Come or to commercial descaler
• Sodium carbonate

To remove mineral deposits

• Vinegar, lemon juice or commercial descaler
• Scrub brush
• Microfiber cloth
  

To clean a shower head with vinegar

Vinegar is the preferred method for cleaning a shower head because the acidity dissolves naturally built up lime scale without the use of hard chemicals.

Step 1: Filling bag with vinegar

Fill a plastic bag partially with distilled white vinegar.Beware not to fill the bag because it can flood when you immerse the shower head.

Step 2: Put the bag over the shower head

Place the bag over the shower head until the entire fixture is immersed in vinegar.If you have to adjust the vinegar level, do it now.

Step 3: Confirm with a rubber band

Attach the bag with a rubber band or turns me around the neck of the shower head.Is a waste that he stays in the shower.)

Step 4: Soft for a few hours

Let the shower head soak for a few hours.Leave it one night for a particularly dirty fixture.If you have a copper bruises, remove them after 30 minutes of vinegar, so longer than this can be damaged and skip this method on nickel -coated shower heads.

Step 5: Remove

Go with the bag and remove it from the shower head.Pour vinegar in the shower (add a little baking powder to remove the protected soap -protected structure in the drain).

Step 6: Run hot water

Run the hot water through the shower head for a minute to wash mineral deposits in the luminaire.

Step 7: Uncleaned nozzles with toothpicks

Use a toothpick or papier mowigip to remove any sprayers that still look hidden.Scrub the fixture with an old toothbrush in dry baking powder if the structure remains.Focus in the areas around the holes where water comes out.Continue the hot water back to the back to rinse even more residue.This process until you no longer see mineral deposits.

Step 8: Polish with cloth

The shower head policy with a soft, lint -free cloth to a finished look.Buff and dry it to remove water stains and help the shower head like new.

If the shower head is removable, make cleaning even easier by immersing the shower head in a bucket -distilled white vinegar.Follow the same cleaning steps after softening and take the fixture again.

To clean a shower head with lemon appasta

If you do not have distilled white vinegar at hand, you can replace a soft in lemon juice and water.Citonsap contains acids that help solve mineral deposits.Follow the same softening and cleaning directions.

If you don't want to wait until the shower head becomes soft, you can clean your shower head with a pasta made of lemon juice and baking powder or lemon juice and salt.Follow these steps.

Step 1: We finish with toothbrush and do it -yourself -cleaning paste

In a cup or small bowl, form a few tablespoons of baking powder or salt with a spray of a little lemon juice.Mix until it forms a pasta.

Step 2: Run hot water

Let the hot water run through the shower head.Remove the shower head so that you can scrub both the inside and the outer of the fixture with the toothbrush.

Step 3: Rinse

Rinse well, collected and grab the shower head again.

You can also use a descaler of the commercial shower head if these natural methods do not work.Follow the instructions for the label carefully.

To clean the filter screen in a shower head

If the shower head still sputtering after cleaning the fixture, it's time to look at the filter screen.

Step 1: Remove the shower head

To do this, screw the fixed fixture by switching it against the clock and pulling it off.You may need a key or lockable tongs.In this case, cover your tools with a cloth and place it over the connecting nut.Squeeze and turn the counter - clockwise to remove the screw of the shower head and pull it off.

Step 2: Turn loose waste

Keep the shower head under a throat and rinse hot water through the interior to erase loose waste.

Step 3: Remove and clean the filter screen

• Remove the filter screen (which is between the shower head and the water pipe).It may be necessary to use a pair of seaweed with needle to pull it away from the mouthpiece.
• Make a solution of equal parts of water and vinegar and water.
• Dip a toothbrush in this solution and scrub the filter rental.You can also use a commercial descaling.
• Lave it under water and dry it with a microfiber cloth.Put the filter back in place.(Buy a new filter screen once a year.)
  

Step 4: Follow the above steps

Clean the rest of the shower head by following the recommended steps above.

Step 5: Reinstall and shower

Replace the shower head and turn it clockwise to put it back together.Drive the shower with full pressure for a few minutes to rinse the remaining waste.

To remove mineral deposits from a shower head

With the help of vinegar, lemon juice or a commercial descaler and a little scrubbing with a scrub brush, removes mineral deposits and helps to remove the shower head.The cleaning agents also remove soap foam that has gathered on the outside of the luminaire.

Follow the above steps to erase the mineral building on the nozzles.

If the nozzles are so hidden that you prefer to replace them instead of cleaning them, search for silicone replacement for shower heads for your specific shower head.

Routine cleaning tips for shower heads

• When you make your weekly cleaning of shower, clean the shower head by spraying it with a solution of equal parts of water and distilled white vinegar or aCommercial detergent.Switch the nozzle openings with a toothbrush and let the shower run for a few minutes to rinse waste.
• With the first sign of reduced water flow, do a thorough cleaning.The mineral deposits only get worse.
• Consider installing an external shower head filter to reduce mineral deposits and bacterial growthThis one from Aquahome, between the shower head and the waterline.
• Choose a metal shower head.Plastic shower heads are more sensitive to wealth growth than metal luminaires.
• Use the bathroom fan during and after bathing to remove the moisture as quickly as possible to reduce mold and mold growth.